Do you use dB or dBm for final fiber optics link test using power meter & light source?
When to use dB and when to use dBm? Most testers get confused between dB and dBm.
It's mathematics and logarithmic unit ( remember the electronics, university and the school ) dB vs. dBm This article appeared in the November 2002 issue of In Tech Magazine Decibel ( dB ) and dB relative to a milliwatt ( dBm ) represent two different but related concepts.
dBm is an absolute power value in milliWatts, it's simply expressed on a logarithmic scale. We use logs in FO power and loss measurements for a host of reasons. dB is a relative measurement, actually a tenth of a Bel ( name after Alexander Graham ) with each Bel being one power of ten.
As dBm (W) is absolute and dB is relative, the following applies. Laser output, dBm. Received power level, dBm. Receiver sensitivity (a range), max dBm to min dBm. Loss of a passive system ( or gain of an active system ), dB. It is simply the measurement of dBm IN minus dBm OUT = dB loss. dB is simply a ration expressed on a log scale.
dBm - dBm = dB
dBm - ( or + ) dB = dBm
Learning aid: Thing of dBm as “ feet above sea level” and dB as “feet”. If you fall from 4500
feet ASL to 2500 feet ASL, you fell 2000 feet. If you fall 2000 feet ASL to Sea Level, you fell 2000 feet.
1. dBm - 5 dB loss = -12 dBm
1. dBm - 5 dB loss = -18 dBm
Sometimes we like to express loss ( diff in power ) simply, so we simple set an arbitrary " 0 dB " (relative) to our laser output power, and measure loss in dB directly from that value. So we define out position (600 feet ASL) as ground level or 0 AGL. If we fly a kite at 100 feet above us, it's 100 feet AGL or 700 feet ASL.
When you deal with instruments, a light source and power meter will measure loss as the difference between two power levels, the " 0 dB reference " and the actual loss test value. Most power meters have a " 0 dB " reference set - a button that will zero the meter at any value in the dB range so you can read loss directly. Since the test power will be lower than the reference power (it's a loss), a power meter will measure loss as a negative number on this test. Some manufacturers of optical loss test sets ( some of whom came into the fiber optic instrument game recently ) make the OLTS read loss as a positive number, highly confusing. Transmitter and receiver power are measured in dBm. The loss of the cable plant is in dB.
The power budget loss of cable plant is calculated in dB, but we use dBm when measured the cable plant loss using power meter and light source. Therefore to relate the calculated and measured values, we deduct measured values in dBm and will get the unit back to dB. For example, if the optical power injected was -22 dBm and the power received at the other end -23 dBm, then the optical loss of the link would be -22 - ( -23 ) = 1 dB. The calculated value in dB gives positive number and measured value in dBm gives neagtive number.
In general dBm and dB are confusing for many technicians. In fact the answer is easy. dBm is absolute power measurement and dB is used for calculation matters only. Also dB is used when you want to know the loss of a link in a network. When doing so you tell your power meter, that its result in dBm should be used as a zero reference. Now put the link in between the both patch cords still on the source and the power meter and you can read the loss in dB. This is only to make things easy because if you change to dBm mode again you will find a result in dBm. If you deduct this value from the original value you will have the result in dB a gain. Most confusion comes up when an equipment guy and a passive guy start talking. The second one thinks in dB, because he has to guarantee a certain loss in the link. The equipment guy only thinks in dBm because his equipment has a certain output in dBm and a certain sensitivity in dBm. His power budget is the difference between the output in dBm and the sensitivity in dBm minus 4 dB (depends on how much reserve you need ). So if the output is 0 dBm and the sensitivity minus 10 dBm he can afford to loose 10 dB minus 4 dB is 6 dB. When measuring with a power meter on the end of the link the reading should be -6 dBm and not -6 dB, because you don't know what is the reference. Here the confusion starts between the two guys, because they don't think alike. So to make things easy: always talk and measure dBm for trouble shooting in networks and dB for testing the passive link only, after you have been able to set a proper reference. If not also use dBm and do the math yourselves afterward.
dB is a percentage value and is used for three types of measurements in fiber optics.
1. Attenuation (power loss) - such as fiber/cable, connectors, splices, splitters and spans.
1. Gain - optical amplifiers/amplification.
1. Reflectance - This could be optical return loss (ORL) or component reflectance such as a SC/UPC or APC connector value.
For more information
没有评论:
发表评论